Custom made in the UK
Free delivery on all UK orders

Click here to visit our store | Download our product catalogue here.

The Joker (Valve Tone)

(2 customer reviews)

£259.00

PRE ORDER NOW
The Joker came from the idea, “what happens if you add controlled distortion to a normally clean booster?”. To achieve this we added an FET based 12AX7 valve simulation with the aim of sounding similar to an overdriven single valve combo.

However, on building a prototype it was found that the pedal had more uses than first envisaged. Firstly, it can do the “small amp tone” as expected. So in “dirt” mode anything from a “warm boost” to a “flat out tweed”. So jazz to blues covered.

A second range (“filth”) was added to allow gain / distortion for rock fans.

Third (unexpected) way of using it is as a boost for a conventional amp but with the added bonus of adding additional harmonic content / tone shaping before hitting the front end of the amp. This gives heavy rock fans the tones they are always looking for.

The green halo light ring installed diffuses the light when playing live, avoiding being blinded by the standard LEDs just as you are about to go into that all important solo thus giving a larger area to see where the pedal is located easily on the pedal board on darkened stages. The addition of the aluminium foot topper gives you more real estate for contact when switching the pedal on and off during quick changes when playing live.

Volume: Controls the volume level of the effect allowing you to cut or push the gain of your amplifier.

Gain: Controls the amount of distortion depending on the position of the toggle switch. In dirt mode it goes from clean to crunch and filth mode allows you to go from crunch to heavily distorted.

Tone: Controls the amount of treble/bass. Fully anti clockwise is max bass boost, mid position gives you a nice lift in the mid ranges and fully clockwise is full treble boost.

Toggle Switch: Selects between “Dirt” and “Filth” settings

  • The Joker comes in a 125B Enclosure (LxWxD): 119x64x40mm (including lid) (69 x 2.52 x 1.57 inch)
  • Standard negative centre,-9v dc tip power supply unit/power brick required
  • No internal 9v dc battery function
  • 20mm anodised aluminium custom etched control knobs
  • Green halo light ring installed
  • The Joker comes with a green custom etched aluminium foot topper
  • This edition comes in a green burst, holographic chrome metal flake and UV printed graphics.

Available on back-order

SKU FGP-LR-TJOK Categories , , ,

Description

Aditional Information

All Flattley “Platinum Range” pedals are hand processed in our Flattley paint shop. The bare aluminium enclosure is abraded prior to painting with the etch primer. The etch primer acts as a anti corrosive layer and allows the primer to bond to the enclosure ensuring a tough resilient paint finish.

Multiple coats of base coat primer are applied which are then lightly abraded to remove any blemishes or paint speckles prior to the application of the base colour. We apply several coats of base colour until an even coverage occurs and the base colour develops rich smooth depth. Metallic holographic chrome flake is then applied using a clear inter coat which adds that all important Flattley sparkle.

The pedal enclosure is now ready to be hydro dipped in its Flattley graphics. This is the process whereby the graphics are applied using water activated film, the residual PVA film is then washed off and the enclosure is then allowed to dry naturally.

Once dried the lacquer process begins. Each “Flattley Platinum” pedal has a minimum of three coats of lacquer which are all wet sanded between coats. Once the lacquer has hardened, it is then hand polished using three different grades of polishing compounds and it then has a final polish to achieve a high gloss finish using a wool finishing pad. This process gives the smooth deep lustre finish that is inherent in all Flattley Guitar and Bass effects pedals.

All our pedals are handmade, hand wired, boutique custom guitar and bass pedal effects manufactured in the UK using only the highest quality components ensuring every aspect of our pedal’s build process results in a truly outstanding product.

Further details can be found on all our social media sites on Instagram/Facebook/LinkedIn/YouTube. Come and follow us/subscribe to see what we do.

2 reviews for The Joker (Valve Tone)

  1. Daniel Mincher

    Very fortunate to get my hands on the Joker pre-release and it’s just amazing! Such a brilliant tone and it has to be one of the best looking pedals around. As soon as I tested the prototype at the London Guitar Show I made sure one of these ended up on my board.
    BZ to Paul and the team

    • Paul Flattley

      We are really happy new “The Joker” product is working well for you and we have been totally blown away how this product has turned out. Its a fantastic pedal and sure it will give you great service for a very long time. Many thanks, best regards Paul

  2. Thomas Manitta

    This Thing is so versatile! You can get everything from tweedy rhythm to sirious lead tones and you always know, wether it´s on or not – even in the sunlight. And for sure it is one of the coolest looking padels! Danger of addiction!

    • Paul Flattley

      Thank you for the very kind words Thomas and we are glad that you love your “The Joker” pedal. Keep rocking, regards Paul

Add a review

Your email address will not be published. Required fields are marked *